mangopi_r
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| mangopi_r [2021/12/03 05:59] – admin | mangopi_r [2025/10/14 06:22] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ~~NOTOC~~ | ||
| + | |||
| + | {{:: | ||
| + | |||
| =====Introduction===== | =====Introduction===== | ||
| This micro development board is specially designed to run Linux. Despite a mini body, it has all the vital functions. Equipped with F1C200S as the maincontroller chip, the board offers various commonly-used peripheral ports: GPIO, I2C & SPI, SDIO, Audio port(record, | This micro development board is specially designed to run Linux. Despite a mini body, it has all the vital functions. Equipped with F1C200S as the maincontroller chip, the board offers various commonly-used peripheral ports: GPIO, I2C & SPI, SDIO, Audio port(record, | ||
| - | |||
| - | Currently, this product is fully open source so that users are allowed to compile any module according to their own requirements. However, it’s mainly for Python developers and senior enthusiasts as it’s a little difficult to get started. | ||
| =====Specification===== | =====Specification===== | ||
| Line 18: | Line 20: | ||
| + | =====Getting Start===== | ||
| + | * https:// | ||
| - | =====R3c===== | + | =====MPi-R1/ |
| - | + | ||
| - | {{:: | + | |
| - | + | ||
| - | + | ||
| - | =====MPi-R1/ | + | |
| * R1 (first commmit) | * R1 (first commmit) | ||
| * R2 (added DVP and audio amp vs R1） | * R2 (added DVP and audio amp vs R1） | ||
| * R3 (fix R2 rtp interrupt, added ctp and buildroot, Mainly the nand version) | * R3 (fix R2 rtp interrupt, added ctp and buildroot, Mainly the nand version) | ||
| * R3c (change to ch340e from CP2104 vs R3) | * R3c (change to ch340e from CP2104 vs R3) | ||
| - | |||
| - | <WRAP group> | ||
| - | =====Buildroot===== | ||
| - | <WRAP half column> | ||
| - | ====正常& | ||
| - | === 启动项: === | ||
| - | * SPI NOR Flash (W25Qxx..) | ||
| - | * SPI NAND Flash (GD5F1GQ4UAxxG..) | ||
| - | * MMC 0 (4-bit TF卡或芯片) | ||
| - | * MMC 1 (1-bit TF芯片，雷龙) | ||
| - | === U-Boot: === | ||
| - | * Basic LCD/ | ||
| - | * SF Devices | ||
| - | * MTD Devices | ||
| - | * USB Peripheral | ||
| - | * USB Mass Storage Drive Enulator | ||
| - | * DFU下载方式 | ||
| - | * TF卡刷方式 | ||
| - | === Linux:=== | ||
| - | * Simple Peripheral: GPIO, SPI, UART, IIC, SDIO, PWM | ||
| - | * DMA Controller | ||
| - | * Audio Codec: Playback, Mic-IN | ||
| - | * USB: OTG Mode, Peripheral Mode, Host Mode | ||
| - | * DVP Camera: OV2640, OV5640 | ||
| - | * Display Engine: Frontend, Backend, TCON | ||
| - | * Keypad ADC | ||
| - | * AW9523B GPIO扩展 | ||
| - | * AXP199 | ||
| - | </ | ||
| - | <WRAP half column> | ||
| - | ==== 正常& | ||
| - | U-Boot 驱动: | ||
| - | * PWM Backlight | ||
| - | Linux 驱动: | ||
| - | * Audio Codec: FM-IN, Line-IN | ||
| - | * IR Receiver | ||
| - | * Cedar Video Engine | ||
| - | ==== 正在开发==== | ||
| - | Linux 驱动: | ||
| - | * TV(CVBS) En/De | ||
| - | </ | ||
| - | </ | ||
| - | |||
| - | |||
| - | |||
| - | ---- | ||
| - | <WRAP group> | ||
| - | <WRAP half column> | ||
| - | =====硬件===== | ||
| - | * [[f1c200_chip|F1C100s/ | ||
| - | * [[TINY200|硬件资料]] | ||
| - | |||
| - | * [[1bittf|SPI位置使用1Bit-TF芯片]] | ||
| - | </ | ||
| - | |||
| - | <WRAP half column> | ||
| - | =====固件===== | ||
| - | * [[mpi-firmware|固件]] | ||
| - | </ | ||
| - | </ | ||
| - | |||
| - | |||
| - | |||
| - | |||
| - | <WRAP group> | ||
| - | <WRAP half column> | ||
| - | =====环境===== | ||
| - | * [[f1c_br|Buildroot环境搭建]] | ||
| - | * [[f1c_mainline|编译]] | ||
| - | </ | ||
| - | |||
| - | <WRAP half column> | ||
| - | =====刷机===== | ||
| - | * [[f1c_flashrom|刷机准备]] | ||
| - | * [[tinyflash|NOR Flash刷机]] | ||
| - | * [[f1c_nand|NandFlash刷机]] | ||
| - | * [[f1c_log|启动LOG]] | ||
| - | </ | ||
| - | </ | ||
| - | * 英文： https:// | + | =====More===== |
| + | [[f1c200s]] | ||
mangopi_r.1638511172.txt.gz · Last modified: (external edit)